Security Link SL150 Guia de Resolução de Problemas Página 52
- Página / 144
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SL150 Installation and Setup Guide
8–4
Programming the 4285/4286 VIP Module
You must program the system for use with the 4285 or 4286 VIP Module. This includes
assigning a phone code and selecting words from the alpha vocabulary. Refer to the
programming sections for specific programming details.
Checking 4285/4286 VIP Module Operation
To Check Operation From an On-Premises Phone:
1. Pick up the phone and enter the programmed 2-digit phone code. Annunciation of a
system status report should automatically start. See the User’s Guide accompanying the
phone module for detailed information regarding the nature of the status report, if
necessary.
2. During any pause in the status report, or immediately following it, key the following via
the keypad on the phone:
4112 (Installer code) + 1 (OFF).
You should hear a beep on the phone and from a wired keypad. You should also hear the
words, "System Ready" or "Not Ready, press star to show faults"* indicating that the
command was entered successfully.
* This voice message would indicate an open zone.
3. Hang up the phone.
To Check Operation from an Off-Premises Phone:
1. Have someone dial the premises phone number, using a TouchTone phone.
• If the phone system does not include an answering machine, 2 long tones will be heard
in the caller’s phone, followed by a voice prompt "Hello, Enter Phone Code Now."
The caller should enter the programmed 2-digit phone code.
• If the premises phone system includes an answering machine, the 2-digit phone code
should be entered during a pause at the beginning of, or during, the outgoing
answering machine message. When the 2-digit phone code is entered, the caller will
hear a voice prompt asking for entry of the 4-digit system code ("Enter System Code
Now").
2. The caller should then enter the installer code (4112). As a safety feature, there is a 3-try
limit in which to enter each code (phone code and system code), after which the call-in will
be aborted. Also, if no keys are pressed for a period of 20 seconds, the call-in is aborted.
Annunciation of a system status report will start if both codes were entered correctly.
3. During any pause in the status report, or immediately following it, the caller should key
the following via the keypad on the phone:
4112 (Installer code) + 1 (OFF).
The caller should hear a beep from the phone and a wired keypad on the premises. The
caller should also hear the words "System Ready" or "Not Ready, press star to show
faults"* * on the phone, indicating that the command was entered successfully.
*
This voice message would indicate an open zone
.
4. At this point, the caller can hang up the phone.
5. Verify with the caller that there was successful access to the system and that the
appropriate annunciations were heard over the phone.
6. If the phone module functioned satisfactorily, unplug the AC transformer from the AC
outlet.
- 6HF XULW\6\VWHP 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- FINAL POWER 12
- Installing the Control 13
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Installing the Backup Battery 18
- Earth Ground Connections 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–8 23
- Remote Keyswitch (Zone 7) 27
- Wired Zone Expansion 33
- Wireless Expansion 37
- 1 2 3 4 5 38
- Installing the 5800TM Module 39
- Jam Detection and Reporting 39
- Appendix A 42
- Powerline Carrier Devices 47
- Programming Relay Outputs 48
- 4285 & 4286 VIP Module 49
- Section 11: 50
- Audio Alarm 50
- Verification (AAV) Unit 50
- 4285/4286 51
- VIP MODULE 51
- External Sounders 53
- Sounder Connections and Power 54
- Sounder Supervision 54
- Testing the Sounder 54
- Long Range Radio 55
- Dynamic Signaling Feature 56
- 4285 or 4286 58
- Final Power-Up 59
- Battery Tests 60
- Mechanics of Programming 61
- Loading Factory Defaults 63
- Exiting the Programming Mode 63
- Data Field Descriptions 69
- OUTPUT TO LONG RANGE RADIO 74
- Allows 81
- Zone Programming 83
- 86
- To Remove a Zone 88
- Section 16 -Zone Programming 91
- Output Device Programming 93
- Zone Lists 99
- Alpha Descriptor Programming 101
- Adding Custom Words 103
- ALPHA VOCABULARY LIST 105
- CHARACTER (ASCII) CHART 105
- Macros (SpeedKey) 107
- Remote Programming and 109
- Control (Downloading) 109
- Remote Programming Commands 110
- Initial Download 110
- System Communication 111
- System Operation 115
- Keypad Functions 116
- Testing the System 121
- Troubleshooting Guide 123
- POSSIBLE CAUSE REMEDY 124
- SYMPTOM POSSIBLE 124
- CAUSE REMEDY 124
- CONTACTING TECHNICAL SUPPORT 125
- In This Section 127
- APPENDIX A 131
- Regulatory Agency Statements 133
- Warnings and Limitations 135
- DOC LOAD NO.: 3 143
- ¬19'l 144
- Two Mid America Plaza 144
- Suite 200 144
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Security Link SL150
(29 páginas)Velleman-projects VM202 Datasheet manuales
Manuales del propietario y guías del usuario para Hardware Velleman-projects VM202 Datasheet.
Ofrecemos 1 manuales en pdf Velleman-projects VM202 Datasheet para descargar gratis por tipos de documentos: Manual de usuario
Comentários a estes Manuais